Stuck on step "Reading Ges5 file..."
Stuck on step "Reading Ges5 file..."
I have already looked in the forum to see if anyone had similar problems, but could not find anything. I am using the latest Micress version 7.100 and ThermoCalc 2018b. When I try to start the simulation, I can't get past the point in the subject. In how far the simulation itself runs at all can not be checked at the moment...
Are version 7.1 and 2018b no longer compatible with each other?
Are version 7.1 and 2018b no longer compatible with each other?
- Attachments
-
- Dendrides_WL_V01_log.txt
- (1.66 KiB) Downloaded 410 times
-
- Dendrides_WL_V01.txt
- (26.04 KiB) Downloaded 390 times
-
- FeCMn1.GES5
- (30.69 KiB) Downloaded 421 times
Re: Stuck on step "Reading Ges5 file..."
Hi PeGr,
there seems to be something wrong with the .GES5-file - has it been created under Windows?
there seems to be something wrong with the .GES5-file - has it been created under Windows?
Re: Stuck on step "Reading Ges5 file..."
Hi PeGr,
works under LINUX with 7.101 for me.
Maybe you should contact your IT to exclude license issues.
Best,
Ralph
works under LINUX with 7.101 for me.
Maybe you should contact your IT to exclude license issues.
Best,
Ralph
Re: Stuck on step "Reading Ges5 file..."
@bernd: yes, it has been created with windows via console mode
@ralph: i got the licences checked beforehand. IT told me i'm good to go...
@ralph: i got the licences checked beforehand. IT told me i'm good to go...
Re: Stuck on step "Reading Ges5 file..."
Is there the possibility, that GES file created via Thermo-Calc 2018b is no longer compatible with Micress 7.100?
I tried an older GES file, which still works with Micress 6.4, to run with 7.1 and i still have the problem, that 7.1 does not read the GES file, eventhough it works with 6.4...
I tried an older GES file, which still works with Micress 6.4, to run with 7.1 and i still have the problem, that 7.1 does not read the GES file, eventhough it works with 6.4...
Re: Stuck on step "Reading Ges5 file..."
Hi PeGr,
usually, there are no problems with TC 2018 and MICRESS 7.1.
As I wrote before, your simulations using your GES5 file is running with 7.1 fine on my side.
Do you use the same environment for 6.4 and 7.1?
I recommend to check it yourself:
- Run Safenet/MICRESS-7.101/Safenet/license_diagnostics-linux.exe in the environment where you execute MICRESS
- Are the database license features you used for creating the GES5 file in there?
Best,
Ralph
usually, there are no problems with TC 2018 and MICRESS 7.1.
As I wrote before, your simulations using your GES5 file is running with 7.1 fine on my side.
What does that mean?@ralph: i got the licences checked beforehand. IT told me i'm good to go...
Do you use the same environment for 6.4 and 7.1?
I recommend to check it yourself:
- Run Safenet/MICRESS-7.101/Safenet/license_diagnostics-linux.exe in the environment where you execute MICRESS
- Are the database license features you used for creating the GES5 file in there?
Best,
Ralph
Re: Stuck on step "Reading Ges5 file..."
Hi ralph,
i am using one of the computers at the institute which are operating on Windows 10 Enterprise. It has both 6.4 and 7.1 installed.
Thanks for your help!
i am using one of the computers at the institute which are operating on Windows 10 Enterprise. It has both 6.4 and 7.1 installed.
If i am doing this, the console pops up for half a second and then closes again. Nothing really happens afterwards. What am i supposed to be experiencing after running the license_diagnostics-win-x64.exe?
Thanks for your help!
Re: Stuck on step "Reading Ges5 file..."
It is a command line tool.
Run 'cmd', navigate with "cd" to MICRESS/Safenet, run license diagnostics.
I thought that you are running under Linux. It is very unlikely that you have different environments for 6.4 and 7.1.
Anyway, it does not hurt to check license diagnostics.
Best,
Ralph
Run 'cmd', navigate with "cd" to MICRESS/Safenet, run license diagnostics.
I thought that you are running under Linux. It is very unlikely that you have different environments for 6.4 and 7.1.
Anyway, it does not hurt to check license diagnostics.
Best,
Ralph
Re: Stuck on step "Reading Ges5 file..."
It is worth trying to run it without MICpad. Maybe some output is not shown.
Drag and drop your driving file to the MICRESS icon on your desktop or the MICRESS_TQ.bat in the MICRESS/Bin folder to check this.
Best,
Ralph
Drag and drop your driving file to the MICRESS icon on your desktop or the MICRESS_TQ.bat in the MICRESS/Bin folder to check this.
Best,
Ralph
Re: Stuck on step "Reading Ges5 file..."
Hi ralph,
thanks for all your efforts. Unfortunately neither the MICpad nor the program itself works for me, it still does not go beyond the point of reading the GESfile...
The license diagnostics doesn't show any issues aswell (as far as i can read it)...
Fe
C: 0,37 wt%
Mn: 0,5 wt%
and the phases: Liquid, BCC_A2, FCC_A1
Thanks for all the help
Peter
thanks for all your efforts. Unfortunately neither the MICpad nor the program itself works for me, it still does not go beyond the point of reading the GESfile...
The license diagnostics doesn't show any issues aswell (as far as i can read it)...
Can you specify what you mean by that? I tried to create a file with the following constellations
Fe
C: 0,37 wt%
Mn: 0,5 wt%
and the phases: Liquid, BCC_A2, FCC_A1
Thanks for all the help
Peter